Sotera FR1118-P10 User Manual download pdf

1. INTRODUCTION

1.1 Technical Data

1.1.1 The turbine digital meter is designed for use with the

following low viscosity fluids:

- Water

- Disel exhaust fluid (DEF)

WARNING!

Use of other fluids may be inaccurate and can damage the meter!

1.1.2 Flow Rate: 3-26GPM, flow rates outside of this range

may have reduced accuracy.

1.1.3 Operating pressure: 4.8BAR/70PSI

1.1.4 Inlet/Outlet: 1”

IMPORTANT!

Not suitable for retail sale of diesel exhaust fluid !

1.2 LCD DISPLAY

The meter display features two numerical registers and

several function or status indicators.

Fig. 1

1.3 USER BUTTONS

The face of the turbine digital meter has two buttons (MENU

and RESET) which individually perform two main functions and

together, other secondary functions.

The main functions performed are:

For the reset key, resetting the partial Register and reset

table total (reset total)

For the menu key, entering instrument calibration mode.

Used together, the two keys permit entering configuration mode.

1.4 BATTERY REPLACEMENT

The battery in your in-line digital meter is not replaceable. To

minimize the possibility of fire or explosion, it is a sealed unit

that does not allow for user replacement. Do not attempt to

open or replace the battery in your meter.

2. INSTALLATION

The inlet and outlet for this meter is 1″BSP/NPT. It can be

easily connected with the pipe or nozzle.

Wait for the meter to go into standby

(blank screen).

With the meter in stand-by mode,

reset the resettable total by

pressing the “RESET” button.

Press and hold the MENU key until

the first digit in the display begins

to flash (approximately 5 seconds).

The meter is in calibration mode.

Press the RESET key to choose the

right digit from 0 to 9. Press the

MENU key to start the next digit.

So the digit of correction factor

can be changed one by one.

Make sure the correction factor is

right, press the MENU key. Keep it

pressed until quit calibration mode,

the factor is saved. The meter goes

to standby again.

Wait for the meter to go to standby.

Reset the resettable total.

Start dispensing into a measuring

glass.

Stop dispensing when 5 Litres of

volume is reached, read out the

actual value. The volume that is

displayed on the LCD is the Display

Value, not the Actual Value which

may be slightly higher. For example,

in the figure on the right, the Display

Value is 18.96 while the Actual

Value is 20.75.

Press the MENU key. Keep it pressed

until showed as the right fig., the digit

flash in ① zone, Press the RESET

key to choose the right digit from

0 to 9. Press the MENU key to go

the the next digit so that the Actual

Value can be input.

Make sure the correction factor is

right and then press the MENU key.

Keep it pressed until calibration is

finished and the factor is saved. The

meter will then return to standby.

Problem

LCD: no indication

Imprecise

measurement

Reduced or zero

flow rate

The meter does

not count, but

the flow rate is

correct

Possible Cause

Bad battery contact

Wrong FACTOR

The meter works

below minimum

acceptable flow rate

Turbine blocked

Incorrect installation

of turbine after

cleaning

Possible electronic

card problems

Corrective Action

Check battery contacts

With reference to

paragraph 3.3 & 3.4,

check the FACTOR

Increase the flow rate

until an acceptable

flow rate range has

been achieved

Clean the turbine.

Repeat the reassembly

process.

Contact Tuthill

Transfer System

Qty.

Description

Meter Cover

Rubber Protection

Electric Board

Self tap screw

Battery Holder

Battery CR2

Meter Body

Qty.

Description

Self tap screw

Turbine

Bearing

Bearing holder

Snap Ring

Circuit board

Self tap screw

Description

Resettable Register (5 digit, from 0.1-99999).

Battery condition.

“Calibration” mode.

Resetting current total to 0.

Totalizer Register (total cumulative fluid dispensed).

Rate of flow being displayed.

Unit of measure (liters, gallons, quarts, pints).

3. DAILY USE

3.1 BUTTON USAGE, CALIBRATION AND MEASUREMENT

UNIT CHANGE

• Reset the present total (See Fig. 2)

1) When the meter is in standby mode, press the RESET key.

2) The display shows all the segments at once.

3) The meter resets to display “0” on the resettable totalizer.

Fig. 2

• Show current correction factor and general total

(See Fig. 3)

Press MENU and RESET together and hold for two seconds.

Value “1.4000” is the correction factor which can be reset;

“1234567” is the general total which cannot be reset.

Fig. 3

• Measurement unit change (See Fig. 4)

Press MENU and RESET together and hold for five seconds.

Zone 7 on the display is the current unit. Press RESET to

chose a different measurement unit and then press MENU to

confirm.

Fig. 4

3.2 RESET THE RESETTABLE TOTALIZER (SEE FIG. 5)

When the meter is in standby, press the RESET key for 2

seconds to reset the totalizer.

Fig. 5

3.3 Calibration Procedure (Using the Correction Factor)

Carefully follow the procedure indicated below.

FORMULA

Proper correction factor =

current correction factor× (actual value / display value)

Example:

Actual value 20.75 Display value 18.96

Current correction factor 1.000

Proper correction factor

1.000×(20.75/18.96)=1.000×1.094=1.094

3.4 MODIFY THE CORRECTION FACTOR IN FIELD

PLEASE CAREFULLY FOLLOW THE PROCEDURE

INDICATED BELOW.

4. MALFUNCTIONS

5. DIAGRAM AND PARTS LIST

DC000440-000 Rev 0

FR1118-P10

User’s Manual

WARNING

Read carefully and understand all INSTRUCTIONS before

operating.

Failure to follow the safety rules and other basic safety

precautions may result in serious personal injury. Save these

instructions in a safe place and on hand so that they can be

read when required.

1 2 3

Summary of Contents

Page 1 - User’s Manual

1. INTRODUCTION1.1 Technical Data1.1.1 The turbine digital meter is designed for use with the following low viscosity fluids:- Water- Disel exhaust fl

Page 2 - Manual del usuario

1. INTRODUCCIÓN1.1 Datos técnicos1.1.1 El medidor digital de la turbina está diseñado para su uso con los siguientes líquidos de baja viscosidad:- Agu

Page 3 - Manuel d’utilisation

3. UTILISATION QUOTIDIENNE3.1 EMPLOI DES BOUTONS, CALIBRAGE ET CHANGEMENT D’UNITÉS DE MESURE• Réinitialiser le total présent (Voir Fig. 2)1) Lorsque l

Comments to this Manuals

No comments

Sotera FR1118-P10 User Manual

Browse online or download User Manual for Equipment Sotera FR1118-P10. Sotera FR1118-P10 User Manual

Summary of Contents

Comments to this Manuals